1 pvc processing aids DLP Series
2 type:acrylic
3 Particle size (40 mesh):>=98%
4 volatiles content(%):<=1.5
PVC Processing Aids DLP Series
1 Product Description
DLP series product is a general PVC processing aid based on emulsion polymerization technology. DLP series can be used in rigid PVC formulations to improve melt flowing,PVC gelation ability and surface quality. It has been widely used in the molding of various PVC products.
2 Performance
Accelerate PVC fusion rate in low temperature, increase cohesion and homogeneity.
Improve PVC rheological property and PVC resin plasticizing. Excellent clarity and surface quality for end-use products, superior fusion promotion for rigid and soft PVC. Increase output rates and improve production efficiency.
3 Typical P hysical Properties
Index
DLP-201
DLP-21
DLP-401
DLP-60
DLP-80
DLP-90
DLP-100
DLP-200
Appearance
White free flowing powder
Particle size (40 mesh passing percentage %)
≥98 % passing
Volatiles Content (%)
≤1.5
Viscosity (η)
3.0-3.5
3.5-4.5
3.5-4.5
6.0-7.5
7.5-8.5
10.5-11.5
9.5-10.5
11.0-12.0
4 Product Category and Properties
Category and Properties
Product
Promote speed
Product
Melt strength
Product
Rheological property
Product
Dispersivity
DLP-200
slow
fast
DLP-201
Low
high
DLP-200
Bad
good
DLP-200
bad
good
DLP-90
DLP-21
DLP-90DLP-90
DLP-401
DLP-60
DLP-60
DLP-60
DLP-60
DLP-80
DLP-80
DLP-80
DLP-80
DLP-100
DLP-90
DLP-100
DLP-100
DLP-201
DLP-100
DLP-201
DLP-201
DLP-21
DLP-200
DLP-21
DLP-21
DLP-401
DLP-401
DLP-401
5 Application
The customers may choose suitable ACR type and the dosage according to different type of product’s features, their needs, the directions for the products and the features of the facilities. If you put forward the specific request, we can recommend you the suitable type and the dosage through experiments.
Sunday, September 4, 2011
PTFE SHEET
1.Great thermostability and chemistry corrosion resistance
2.Great electricity performance
Description:
PTFE resin molded sheet is manufactured by molding with PTFE granular resin.
APPLICATION:
Lining Bearing pads, seals, and electrical insulation
length×width(mmXmm)
Thickness(mm)
Tolerance
150×150
1.0~30
±0.30~±0.50
250×250
1.5~30
±0.30~±0.50
300×300
1.5~30
±0.30~±0.50
450×450
1.5~30
±0.30~±0.50
600×600
2~30
±0.30~±0.50
800×800
2~30
±0.30~±0.50
1000×1000
3~30
±0.30~±0.50
1200×1200
3~30
±0.30~±0.50
1000 ×2000
5~35
±0.30~±0.60
TECHNICAL DATA:
Te chnical data
unit
Result
Apparent density
g/cm3
2.10~2.30
Tensile strength(min)
MPa
15.0
Ultimate elongation(min)
%
150
Dielecric strength(min)
Kv/mm
10
ADVANTAGES:
1.Minimal Water Absorption
2.Excellent Machining
3.Acid and chemical resistant
4.Good Electrical insulation
5.High working temperatures
6.Low friction
2.Great electricity performance
Description:
PTFE resin molded sheet is manufactured by molding with PTFE granular resin.
APPLICATION:
Lining Bearing pads, seals, and electrical insulation
length×width(mmXmm)
Thickness(mm)
Tolerance
150×150
1.0~30
±0.30~±0.50
250×250
1.5~30
±0.30~±0.50
300×300
1.5~30
±0.30~±0.50
450×450
1.5~30
±0.30~±0.50
600×600
2~30
±0.30~±0.50
800×800
2~30
±0.30~±0.50
1000×1000
3~30
±0.30~±0.50
1200×1200
3~30
±0.30~±0.50
1000 ×2000
5~35
±0.30~±0.60
TECHNICAL DATA:
Te chnical data
unit
Result
Apparent density
g/cm3
2.10~2.30
Tensile strength(min)
MPa
15.0
Ultimate elongation(min)
%
150
Dielecric strength(min)
Kv/mm
10
ADVANTAGES:
1.Minimal Water Absorption
2.Excellent Machining
3.Acid and chemical resistant
4.Good Electrical insulation
5.High working temperatures
6.Low friction
Tape primer for foam tape and EPDM,PP,TPE rubber
CNHYBOND 944
Tape primer/Promote adhesion/adhesion promote
Technical Data
Product Description
CNHYBOND 944 Tape primer
CNHYBOND 944
Tape primer/Promote adhesion/adhesion promote
Technical Data
Product Description
CNHYBOND 944 Tape primer
can be used to promote adhesion of double side adhesive(such as 3M VHB, 3M9080 , 3M9448 , Japan 5000NS, SONY T4000 , T4720 , TESE4940 etc.) to surfaces such polypropylene,EPDM,TPU,ABS,PET/PBT blends, concrete, wood, glass, metal and painted metal surfaces. IT is success replace : 3M K-500,3M K-520,3M 4298,,3M 94,3M4298
Typical Physical properties and Performance Characteristics
Note:
The following technical information and data should be considered representative or typical only and should not be used for specification purposes
S
olids: Approximately 5%-8%
Col or: clear light yellow
Flashpoint: -4°F(-20°C)
Net Weight: 780-800grams per liter
Viscosity: 40±5cps
Application Techniques
Surface preparation:
The bonding surface must be relatively clean and dry.Contaminated surfaces should be cleaned with a 50/50 Isopropyl Alcohol and water mixture,A clean lint-free cloth should be used.
Application
:Shake CNHYBOND 944 primer well before using:
Apply a thin uniform coating to the bonding surface using the minimum amount that will fully coat the surface, allow cnhybond 944 primer to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature, Be sure the primed surface remains free from contaminants prior to applying the tape. Porous surfaces may require 2 application of CNHYBOND 944 primer for uniform coverage and good adhesion..
Allow first application of primer to dry before applying the second coat, CNHYBOND primer 944 may be applied with brush or swab, It can also be applied with a pressurized flow gun, knurled roller or other similar type of application equipment
Application Techniques
Surface preparation:
The bonding surface must be relatively clean and dry.Contaminated surfaces should be cleaned with a 50/50 Isopropyl Alcohol and water mixture,A clean lint-free cloth should be used.
Application
:Shake CNHYBOND 944 primer well before using:
Apply a thin uniform coating to the bonding surface using the minimum amount that will fully coat the surface, allow cnhybond 944 primer to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature, Be sure the primed surface remains free from contaminants prior to applying the tape. Porous surfaces may require 2 application of CNHYBOND 944 primer for uniform coverage and good adhesion..
Allow first application of primer
to dry before applying the second coat, CNHYBOND primer 944 may be applied with brush or swab, It can also be applied with a pressurized flow gun, knurled roller or other similar type of application equipment
Tape primer/Promote adhesion/adhesion promote
Technical Data
Product Description
CNHYBOND 944 Tape primer
CNHYBOND 944
Tape primer/Promote adhesion/adhesion promote
Technical Data
Product Description
CNHYBOND 944 Tape primer
can be used to promote adhesion of double side adhesive(such as 3M VHB, 3M9080 , 3M9448 , Japan 5000NS, SONY T4000 , T4720 , TESE4940 etc.) to surfaces such polypropylene,EPDM,TPU,ABS,PET/PBT blends, concrete, wood, glass, metal and painted metal surfaces. IT is success replace : 3M K-500,3M K-520,3M 4298,,3M 94,3M4298
Typical Physical properties and Performance Characteristics
Note:
The following technical information and data should be considered representative or typical only and should not be used for specification purposes
S
olids: Approximately 5%-8%
Col or: clear light yellow
Flashpoint: -4°F(-20°C)
Net Weight: 780-800grams per liter
Viscosity: 40±5cps
Application Techniques
Surface preparation:
The bonding surface must be relatively clean and dry.Contaminated surfaces should be cleaned with a 50/50 Isopropyl Alcohol and water mixture,A clean lint-free cloth should be used.
Application
:Shake CNHYBOND 944 primer well before using:
Apply a thin uniform coating to the bonding surface using the minimum amount that will fully coat the surface, allow cnhybond 944 primer to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature, Be sure the primed surface remains free from contaminants prior to applying the tape. Porous surfaces may require 2 application of CNHYBOND 944 primer for uniform coverage and good adhesion..
Allow first application of primer to dry before applying the second coat, CNHYBOND primer 944 may be applied with brush or swab, It can also be applied with a pressurized flow gun, knurled roller or other similar type of application equipment
Application Techniques
Surface preparation:
The bonding surface must be relatively clean and dry.Contaminated surfaces should be cleaned with a 50/50 Isopropyl Alcohol and water mixture,A clean lint-free cloth should be used.
Application
:Shake CNHYBOND 944 primer well before using:
Apply a thin uniform coating to the bonding surface using the minimum amount that will fully coat the surface, allow cnhybond 944 primer to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature, Be sure the primed surface remains free from contaminants prior to applying the tape. Porous surfaces may require 2 application of CNHYBOND 944 primer for uniform coverage and good adhesion..
Allow first application of primer
to dry before applying the second coat, CNHYBOND primer 944 may be applied with brush or swab, It can also be applied with a pressurized flow gun, knurled roller or other similar type of application equipment
94% Sodium Tripolyphosphate tech grade
94% Sodium Tripolyphosphate tech grade
(1)good quality
(2)competetive price
(3)timely delivery
(4)excellent service.
94% Sodium Tripolyphosphate tech grade
Specification:
Na
5
P
3
O
10
,% ,Min.
94
P
2
O
5
,% ,Min.
57
Insolubles, % Max.
0.05
PH Value(1%Solution)
9.5-10.0
Iron (Fe), %, Max.
0.015
Fluoride (F), %, Max.
0.003
Chloride (Cl), %, Max.
0.025
Sulphate (as SO
4
), %, Max.
0.4
Bulk density, g/l
650-990
White degree %,Min.
93
Phase I
10-30
Packing:25kg plastic bags, 25MT per 20'FCL or as per buyers' requirement
Sodium Tripolyphosphate 94% STPP GENERAL INFORMATION
HS CODE
2835310000
CAS NO
7758-29-4
GRADE
national standard china
FORMULA
Na5P3O10
MOLECULAR WEIGHT
367 .86
94% Sodium Tripolyphosphate STPP PROPERTIES
Appearance
White powder
Melting Point
622°C
Boiling Point
1000°C
(1)good quality
(2)competetive price
(3)timely delivery
(4)excellent service.
94% Sodium Tripolyphosphate tech grade
Specification:
Na
5
P
3
O
10
,% ,Min.
94
P
2
O
5
,% ,Min.
57
Insolubles, % Max.
0.05
PH Value(1%Solution)
9.5-10.0
Iron (Fe), %, Max.
0.015
Fluoride (F), %, Max.
0.003
Chloride (Cl), %, Max.
0.025
Sulphate (as SO
4
), %, Max.
0.4
Bulk density, g/l
650-990
White degree %,Min.
93
Phase I
10-30
Packing:25kg plastic bags, 25MT per 20'FCL or as per buyers' requirement
Sodium Tripolyphosphate 94% STPP GENERAL INFORMATION
HS CODE
2835310000
CAS NO
7758-29-4
GRADE
national standard china
FORMULA
Na5P3O10
MOLECULAR WEIGHT
367 .86
94% Sodium Tripolyphosphate STPP PROPERTIES
Appearance
White powder
Melting Point
622°C
Boiling Point
1000°C
Polyaluminium chloride-04
polyaluminium chloride is a new high--efficiency unorganic polymer coagulating agent
Product perfomance
1,Become flocculant in high speed,big block, high activity and rapid sedimentation analysis.
2,It doesn't need other accessory ingredients and use less additional chenical
reabents than other unorganic coagulating agents and has lower cost for making water.
3,It has far--ranging PH value and strong dadptability and good effect for hithly turbid high--temperature organic contaminated water and lowly turbid low--temperature or ganic contaminated water.
PAC-04
Item
Al2O3 27.0%min
Basicity 80-95
Water insolvent 1.5% max
PH 3.5-5.0
N 0.01%max
As 0.0001%max
Cr6+ 0.0005%max
Hg 0.00001%max
Pb 0.0005%max
Cd 0.0001% max
Use:
for
domestic sewage and various kind industrial wastewater treatment.
Product perfomance
1,Become flocculant in high speed,big block, high activity and rapid sedimentation analysis.
2,It doesn't need other accessory ingredients and use less additional chenical
reabents than other unorganic coagulating agents and has lower cost for making water.
3,It has far--ranging PH value and strong dadptability and good effect for hithly turbid high--temperature organic contaminated water and lowly turbid low--temperature or ganic contaminated water.
PAC-04
Item
Al2O3 27.0%min
Basicity 80-95
Water insolvent 1.5% max
PH 3.5-5.0
N 0.01%max
As 0.0001%max
Cr6+ 0.0005%max
Hg 0.00001%max
Pb 0.0005%max
Cd 0.0001% max
Use:
for
domestic sewage and various kind industrial wastewater treatment.
pu resin (Anti-yellowing bright surface agent) chemicals for leather
pu resin LU-201G
1.have TEST REPROT. excellent transparency,
2.anti-yellowing,
3.Solid content: 19%
4.package:190kg/drum.
pu resin LU-201G(
Anti-yellowing bright surface agent
) chemicals for leather
n Appearance: semi-transparent liquid
n Solid content: 19±1%
n Viscosity: 200~600 CPS/25°C
n 100% module:
n Solvents: DMF/MEK/BAC/IPA
n Property:
excellent transparency
n Reference formulation:100 head to treat
n Caution notes:
Please store it in cool dry places with good ventilation.
1.have TEST REPROT. excellent transparency,
2.anti-yellowing,
3.Solid content: 19%
4.package:190kg/drum.
pu resin LU-201G(
Anti-yellowing bright surface agent
) chemicals for leather
n Appearance: semi-transparent liquid
n Solid content: 19±1%
n Viscosity: 200~600 CPS/25°C
n 100% module:
n Solvents: DMF/MEK/BAC/IPA
n Property:
excellent transparency
n Reference formulation:100 head to treat
n Caution notes:
Please store it in cool dry places with good ventilation.
Anti yellow agent
Anti yellow agent
1.Colorless,transparent liquid and odorless
2.ISO certified
3.Purity:100%
Anti yellow agent
1. Name of Commodity:
H202-A, Anti yellow agent
2.
Technical Indexes:
Appearance
Colorless, transparent liquid and odorless
Purity
100%
Viscosity(25
o
C)
20~30 mm
2
/s
Dioptre/n
25
D
1.390-1.410
Density/25
o
C
1.050-1.100g/cm3
Volatilization/105
o
,3H
≤0.8
PH
7
3. Properties & Applications
H202-A as anti yellow agent specially for silicone rubber, it has a good effect to prevent silicone rubber products from white become yellow when the second vulcanizing proceeds.
crude rubber mixed with carbon-white it called gross rubber(HTV rubber), as anti yellow agent it has a good effect according to this r ate, anti yellow agent : HTV rubber = 5:1000
4. Storage and Transportation:
Packing is 200L iron drum (net weight is 200kg/barrel),80drums/20’fcl .
It should be stored in shady, cool, dry and ventilated storehouse;
It should be kept away from fire and heat sources, the temperature in warehouse should be not exceed 30°C;
Package should be need airproof and avoid direct sunlight;
It should be put and stored far away oxidant, acid and edible chemical materials;
It should be adopt protection against explode at storage, don't use tool of producing spark easily;
It should be control packing speed when filling for fearing static;
Transportation: As non-hazardous chemicals;
Quality guarantee period: 12 months. Beyond the time, it still can be used only after the result of recheck is up to this standard.
.
1.Colorless,transparent liquid and odorless
2.ISO certified
3.Purity:100%
Anti yellow agent
1. Name of Commodity:
H202-A, Anti yellow agent
2.
Technical Indexes:
Appearance
Colorless, transparent liquid and odorless
Purity
100%
Viscosity(25
o
C)
20~30 mm
2
/s
Dioptre/n
25
D
1.390-1.410
Density/25
o
C
1.050-1.100g/cm3
Volatilization/105
o
,3H
≤0.8
PH
7
3. Properties & Applications
H202-A as anti yellow agent specially for silicone rubber, it has a good effect to prevent silicone rubber products from white become yellow when the second vulcanizing proceeds.
crude rubber mixed with carbon-white it called gross rubber(HTV rubber), as anti yellow agent it has a good effect according to this r ate, anti yellow agent : HTV rubber = 5:1000
4. Storage and Transportation:
Packing is 200L iron drum (net weight is 200kg/barrel),80drums/20’fcl .
It should be stored in shady, cool, dry and ventilated storehouse;
It should be kept away from fire and heat sources, the temperature in warehouse should be not exceed 30°C;
Package should be need airproof and avoid direct sunlight;
It should be put and stored far away oxidant, acid and edible chemical materials;
It should be adopt protection against explode at storage, don't use tool of producing spark easily;
It should be control packing speed when filling for fearing static;
Transportation: As non-hazardous chemicals;
Quality guarantee period: 12 months. Beyond the time, it still can be used only after the result of recheck is up to this standard.
.
Subscribe to:
Comments (Atom)